nó bị thiếu thư viện đó rồi nha bạn, bạn ra mạng gõ VCOMP100.DLL rồi download về cài đặt vào rồi khởi động lại máy rồi chạy lại game đó xem thử ok ko nha bạn. game này mình chơi rồi cài xong nó thiếu nhiều dll lắm cứ lên mạng dow xong add vào đủ hết là chơi được Hi, Just downloaded on Windows 10. When I click to open, I press Play than Play again, and it says 'preparing to launch' and that pop up keeps opening and closing and nothing happens... any ideas? Lần sửa cuối bởi emailmpn;23 Thg09, 2016 @ 12:39am Đang hiển thị 1-10 trong 10 bình luận  Same here! At first I had the screen spinning problem. After I updated my XBone controller firmware, the game won't open at all. WTF. Can anybody help? RECOMMENDED: OS: Windows Vista, Windows 7, Windows 8. ...what the hell? did u install direct11? i run it with windows partitioned on a mac book. runs smoothly with no problem. Also windows 10 here @DeathWantsMore, Is that seriously your solution? Install Windows 8? For one game? A. I don't think that's the problem, and B. If it is, that's still completely unnacceptable. @ConquerV Yes, I obviously have DX11. Even if I didn't beforehand, it's included in the game files and would automaticaly install itself. Amora Hello, I'm playing normally on Windows 10 here, so it's not an OS problem. DirectX 11 isn't something that is 'installed', it's a resource built-in your video board, plus the game requires DX9 to run, so your video board is probably enough to run it (unless you're playing games in a toaster). First I would recommend going to <Steam install directory>/steamapps/common/Dynasty Warriors 8/_CommonRedist and run both DirectX/Jun2010/DXSETUP.exe and vcredist/2010/vcredist_x64.exe (vcredist_x86.exe if your OS is 32 bit). If it doesn't run, try updating your video board drivers and check the integrity of the game files (on Steam, right-click on the game on Library, go in Properties > Local Files > Verify integrity of game cache). If even then it doesn't run, press Windows + R, type dxdiag on the box and paste the System Info here, 'cause something is problem wrong there. Same here! At first I had the screen spinning problem. After I updated my XBone controller firmware, the game won't open at all. WTF. Can anybody help? RECOMMENDED: OS: Windows Vista, Windows 7, Windows 8. ...what the hell? did u install direct11? i run it with windows partitioned on a mac book. runs smoothly with no problem. Also windows 10 here @DeathWantsMore, Is that seriously your solution? Install Windows 8? For one game? A. I don't think that's the problem, and B. If it is, that's still completely unnacceptable. @ConquerV Yes, I obviously have DX11. Even if I didn't beforehand, it's included in the game files and would automaticaly install itself. Amora Hello, I'm playing normally on Windows 10 here, so it's not an OS problem. DirectX 11 isn't something that is 'installed', it's a resource built-in your video board, plus the game requires DX9 to run, so your video board is probably enough to run it (unless you're playing games in a toaster). First I would recommend going to <Steam install directory>/steamapps/common/Dynasty Warriors 8/_CommonRedist and run both DirectX/Jun2010/DXSETUP.exe and vcredist/2010/vcredist_x64.exe (vcredist_x86.exe if your OS is 32 bit). If it doesn't run, try updating your video board drivers and check the integrity of the game files (on Steam, right-click on the game on Library, go in Properties > Local Files > Verify integrity of game cache). If even then it doesn't run, press Windows + R, type dxdiag on the box and paste the System Info here, 'cause something is problem wrong there. |
