The [1.2.1] is a numerical based menu, used to configure a server core.

On this page:

  • Install Server Core
  • Set the administrative password
  • Set a static IP address
  • Join a domain
  • Rename the server
  • Activate the server
  • Configure the firewall
  • Administrative credentials
  • Known issues for configuring a Server Core installation

Install Server Core

To manually install and configure a Server Core installation of Windows Server 2008:

  1. Insert the appropriate Windows Server 2008 installation media into your DVD drive.
  2. When the auto-run dialog box appears, click .
  3. Follow the instructions on the screen to complete Setup.
  4. After Setup completes, press Ctrl-Alt-Del, click , type Administrator with a blank password, and then press Enter. You will be prompted to set a password for the Administrator account.

Set the administrative password

  1. When your computer starts for the first time after the installation completes, press Ctrl-Alt-Del. Type Administrator for the user name and leave the password blank.
  2. The system will inform you that the password has expired and will prompt you to enter a new password.
  3. Type an appropriate password.

Set a static IP address

  1. At a command prompt, type: netsh interface ipv4 show interfaces
  2. Make a note of the number shown in the "Idx" column of the output for your network adapter. If your computer has more than one network adapter, make a note of the number corresponding to the network adapter for which you wish to set a static IP address.
  3. At the command prompt, type on one line: netsh interface ipv4 set address name="<ID>" source=static address=<StaticIP> mask=<SubnetMask> gateway=<DefaultGateway>

    In the above command:

    • "ID" is the number from step 2 above.
    • "StaticIP" is the static IP address that you are setting.
    • "SubnetMask" is the subnet mask for the IP address.
    • "DefaultGateway" is the default gateway.
  4. At the command prompt, type: netsh interface ipv4 add dnsserver name="<ID>" address=<DNSIP>index=1

    In the above command:

    • "ID" is the number from step 2 above.
    • "DNSIP" is the IP address of your DNS server.
  5. Repeat step 4 for each DNS server that you want to set, incrementing the index= number each time.

Note:

If you set the static IP address on the wrong network adapter, you can change back to using the DHCP address supplied by using the following command:

netsh interface ipv4 set address name="<ID>" source=dhcp

In the above command, "ID" is the number of the network adapter from Step 2.

Join a domain

  1. At a command prompt, type: netdom join <ComputerName> /domain:<DomainName> /userd:<UserName> /password:*

    In the above command:

    • "ComputerName" is the name of the server that is running the Server Core installation.
    • "DomainName" is the name of the domain to join.
    • "UserName" is a domain user account with permission to join the domain.
  2. When prompted to enter the password, type the password for the domain user account specified by UserName.
  3. If you need to add a domain user account to the local Administrators group, type the following command: net localgroup administrators /add <DomainName>\<UserName>
  4. Restart the computer. You can do this by typing the following at a command prompt: shutdown /r /t 0

Rename the server

  1. Determine the current name of the server with the hostname or ipconfig command.
  2. At a command prompt, type: netdom renamecomputer <ComputerName> /NewName:<NewComputerName>
  3. Restart the computer.

Activate the server

At a command prompt, type:

slmgr.vbs -ato

If activation is successful, no message will return in the command prompt.

Note:

You can also activate by phone, using a Key Management Service (KMS) server, or remotely by typing the following command at a command prompt of a computer that is running Windows Vista or Windows Server 2008:

cscript windows\system32\slmgr.vbs <ServerName> <UserName> <password>:-ato

Configure the firewall

Use the netsh advfirewall command. For example, to enable remote management from any MMC snap-in, type:

netsh advfirewall firewall set rule group="Remote Administration" new enable=yes

Note:

You can also use the Windows Firewall snap-in from a computer running Windows Vista or Windows Server 2008 to remotely manage the firewall on a server running a Server Core installation. To do this, you must first enable remote management of the firewall by running the following command on the computer running a Server Core installation:

netsh advfirewall set currentprofile settings remotemanagement enable

Administrative credentials

If you are going to join a server running a Server Core installation to an existing Windows domain, you need a user name and password for an account that has the administrative credentials to join a computer to the domain.

Known issues for configuring a Server Core installation

  • If you close all command prompts, you will have no way to manage the Server Core installation. To recover, you can press Ctrl-Alt-Del, click , click , click , and type cmd.exe. Alternatively, you can log off and log back on again.
  • Because there is no web browser, you cannot activate a Server Core installation or access the internet through a firewall that requires users to log on.

The information in this document was originally adapted from Windows documentation.

This is document awst in the Knowledge Base.
Last modified on 2021-09-20 16:36:47.

Which of the following used to configure and manage in Server Core?

You can use many snap-ins for Microsoft Management Console (MMC) remotely to manage your Server Core server. To use an MMC snap-in to manage a Server Core server that is a domain member: Start an MMC snap-in, such as Computer Management. Right-click the snap-in, and then click Connect to another computer.

What tool is commonly used for initial configuration of Server Core?

You can use the Server Configuration tool (SConfig) to configure and manage a Windows Server instance or Azure Stack HCI. When Windows Server is installed with the Server Core installation option, SConfig is the primary way to configure and manage common aspects of the operating system, including: Network configuration.

Which command is used to configure Windows Server 2012 r2 core?

Configuring basic settings on Server Core installations of Windows Server 2012 is easy with sconfig. cmd, but it can also be done and scripted using other tools.

What is Server Core used for?

Windows Server Core is a minimal installation option for the Windows Server operating system (OS) that has no GUI and only includes the components required to perform server roles and run applications.